Definition, Betydelse & Anagram | Engelska ordet SOLDERED

Definition av SOLDERED

1. böjningsform av solder
2. perfektparticip av solder

Exempel på hur man kan använda SOLDERED i en mening

• During the Civil War, berries were hand-picked, hand-canned and soldered for shipping to the Union Army.
• Exquisite goldwork represents an old Philippine wealth in both an economic and an artistic sense: all sorts of wrought or molded ornaments and jewelry demonstrate both the availability of the raw material and the skill of the artisan – finger rings, earrings, head-bands, pendants, and pectoral ornaments, heavy chains with interlocking serrated edges, light filigree work, delicate necklaces of fine twisted wires, 12-millimeter beads composed of 184 separate granules soldered together, thin hammered sheets for decorating grosser objects like earplugs or the visages of corpses, and a charming little snail of unknown use.
• In addition to the main figures which are soldered to the horn, protruding from the horn surface, there are a number of additional figures and ornaments realized by chasing.
• Discrete transistors are soldered to circuit boards, with interconnections accomplished by stencil-screened conductive patterns on the reverse side.
• As with other stripboards, in using Veroboard, components are suitably positioned and soldered to the conductors to form the required circuit.
• His early work used soldered and welded metal as well as junk materials, and by 1960 César was considered one of France's leading sculptors.
• Barker and Midlock cobbled a Doppler radar unit from coffee cans soldered shut to make microwave resonators.
• Another notable evidence against Kim was the teeth of her comrade Kim Sung Il, who had cavities which had been filled with soldered lead, a common method of cavity treatment in dentistry in North Korea.
• Taps are normally connected to the water supply by means of a "swivel tap connector", which is attached to the end of the water pipe using a soldered or compression fitting, and has a large nut to screw onto the threaded "tail" of the tap, which hangs down underneath the bath, basin or sink.
• In the three-hole kind of instrument, there are two yaw direction tubes which are chamfered and silver soldered symmetrically on the two sides of a pitot tube.
• When manufactured for electronics testing and evaluation, one jaw of the clip is typically permanently crimped or soldered to a wire, or is bent to form the inner tubular contact of a ~ female banana jack, enabling quick non-permanent connection between a circuit under test and laboratory equipment or to another electrical circuit.
• The other end of the plug has a lug connector to which a length of flexible insulated equipment wire can be attached, which is either screwed, soldered, or crimped into place.
• In contrast with a BGA, land grid array packages in non socketed configurations have no balls, and use flat contacts which are soldered directly to the PCB.
• Like any other surface-mount inductor, these are soldered into a gap in the printed circuit board trace.
• Ends can then be hemmed in and soldered, or flanged and brazed (and/or sealed with an epoxy-type sealant) or the ends can be flanged and then welded.
• The name evokes the technique of cloisonné, where wires (cloisons or "compartments") are soldered to the body of the piece, filled with powdered glass, and then fired.
• Like most gold alloys, tumbaga was versatile and could be cast, drawn, hammered, gilded, soldered, welded, plated, hardened, annealed, polished, engraved, embossed, and inlaid.
• Original Firebird pickups were also built without any specific bobbin fasteners — their bobbins (and possible "reflector" plate under the bobbins) were held onto the frame during both the wax potting process (to reduce/eliminate feedback and unwanted noise) and the solid metal cover that was soldered to the frame base.
• Cristian Bosc, Italian brass instrument maker, has improved the axial flow valve design by fabricating both the rotor and the valve casing from single pieces of solid brass with no soldered parts.
• Large surfaces of gold are sometimes covered with scrolls of filigree soldered on, and corner pieces of the borders of book covers, or the panels of reliquaries, are frequently made up of complicated pieces of plaited work alternating with spaces encrusted with enamel.

Förberedelsen av sidan tog: 109,37 ms.